Hiro H50194 Bedienungsanleitung

1 Wireless USB Adapter User’s Manual

10Step 5: Click " Next ". Step 6: Click " Install ".

11Step 7: Click " Finish ".

12Windows XP Step 1: As Windows starts it will detect that new hardware has been added, and start the " Found New Hardware Wizard ". Click

13Step 2: Please insert the AUTORUN CD into your CD-ROM drive. The CD should auto-start, displaying the following window. If it does not start, clic

14Step 3: Click " Next ". Step 4: Click " Next ".

15Step 5: Click " Install ". Step 6: Click " Finish ".

16Windows 2000 Step 1: As Windows starts it will detect that new hardware has been added, and start the " Found New Hardware Wizard ". Cl

17Step 2: Please insert the AUTORUN CD into your CD-ROM drive. The CD should auto-start, displaying the following window. If it does not start, clic

18Step 3: Click " Next ". Step 4: Click " Next ".

19Step 5: Click " Install ". Step 6: Click " Finish ".

2Table of Contents USER’S MANUAL...

20Making a Basic Wireless Network Connection For Windows XP/Vista/7 users, your native Windows XP/Vista/7 wireless support (Wireless Zero Configurat

21Step 2: Click the " Available Network " button to scan available access points. Step 3: Double click on the SSID of AP that you are go

22Step 4: Click the " OK ". Step 5: Click the " OK ".

23Step 6: Now you are ready to use the Wireless Network to Internet or intranet. Note: This example is an open wireless network. If you are going

24Introduction to the Wireless LAN Utility Note: This management instruction uses Windows XP/Vista/7 as the presumed operation system. Starting

25General After starting the utility, the general page pops up This General tab provides the information of your current wireless network connectio

26Profile The Profile tab lists the preferred connections. You can click the buttons beside to do configure each connection. Functions Add To a

27Available Network This Available Network tab lists the reachable wireless network. Functions Refresh To rescan available Wireless Networks. A

28Status The Status tab shows the current connection status.

29Statistics The Statistics tab shows the transmission activity record. Clicking the " Reset " button recounts the values from zero.

3Welcome Thank you for purchasing the IEEE 802.11n Wireless USB Adapter. Wireless USB Adapter has an extra foundation which is designed to make Wire

30Wi-Fi Protected Setup (WPS) An easy and secure setup solution for Wi-Fi network.

31Push Button Config (PBC) Method If both AP and users’ Wireless LAN Utility has the physical button or visual button of Push Button Config (PBC),

32Step 2: Click on " Push Button Config (PBC) " button.

33Step 3: Now you are ready to use the Wireless Network to Internet or intranet.

34PIN Method 2 If AP know users’ PIN code and the PIN code is 87489095, please follow steps below to complete the WPS. Step 1: Double click the

35Step 2: Click on " Pin Input Config (PIN) " button. Step 3: Click on " Yes " button.

36Step 4: Select the desired WPS AP Name and then click on " Select " button. Step 5: Please enter the PIN Code into your AP.

37Step 6: Now you are ready to use the Wireless Network to Internet or intranet.

38Uninstall Step 1: Click " Start -> All Programs -> REALTEK 11n USB Wireless LAN Utility -> Uninstall ". Step 2: Click "

39Step 3: Click " Finish ".

4Wireless USB Adapter Overview Wireless USB Adapter has the USB interface, LED and WPS button below. Interface USB Interface: Connect the USB Inter

40Troubleshooting Session Overlap If there is more then one AP on the PBC mode, there will be [Session Overlap].Please using PIN method or wait for

41REALTEK 11n USB Wireless LAN is Disconnected If you see the message below, please refer to the chapter Making a Basic Wireless Network Connection

5Wireless USB Adapter Installation The following instructions will guide you to through the process of installing the Wireless USB Adapter. Windows

6Step 4: Click " Next ". Step 5: Click " Next ".

7Step 6: Click " Install ". Step 7: Click " Finish ".

8Windows Vista Step 1: As Windows starts it will detect that new hardware has been added, and start the " Found New Hardware Wizard ". Cli

9Step 3: For Security reasons VISTA requires the installer program to have administrator privileges so the new policy called " User Account Con